GPM Hydraulic Gear Pumps

GPM Bushing Gear Pump Range

Bushing Gear Pump Range

Series 215
Series 230
Series 250
Series 265

Hydraulic

  • Pumps
  • Motors
  • Flow Dividers
  • Add-a-Pumps
  • Step-Down Pumps
  • Spare Parts

Speeds up to: 3000 RPM
Pressure up to 240 BAR
Displacements between 10cc/rev to 147 cc/rev

Click on the BLUE SHADED headlines to open and close pages

Motor Specifications

GPM Bushing Pump & Motor Specifications

Major Features, Interchangeability and PL Factor

PUMPS & MOTORS

Fluid Power for Mobile Equipment

GPM hydraulic pumps and motors are particularly well suited to mobile equipment applications; they are designed for extreme duty cycles, and continuous heavy duty operation. Whilst the equipment is of a simple yet rugged design, it is manufactured to extremely precise tolerances.

Pumps are available in capacities ranging from 11 cc/rev to 200 cc/rev for each gear section. Several sections can be combined into one assembly. A wide selection of SAE and ANSI mounting flanges and drive shafts are available for all drive units. Pipe thread, 0-ring seal, and split flange ports are available in both metric and SAE standards.

GPM pumps are manufactured under statistical analysis process control which is monitored by the South African Bureau of Standards to an ISO 9001-2008 quality management system.

Major Features

Sectional Construction: Standard Parts can be assembled in a wide variety of configurations to suit almost any application. All gear housings are cast from an extra complex iron with a minimum tnsile strength of 380 Mpa (55000 Psi) and hardness between 200 and 250 Brinell.

Multiple pump units: Several pump sections can be combined in a single drive, to eliminate multiple drive P.T.O units. Precision matched gears: All gears are manufactured from high alloy forged bars, surfaces are super finished and each gear pair is matched for maximum efficiency. The deep 1 0-tooth pattern gives maximum output per revolution whilst ensuring low pulsation frequency.

Bearings: Latest technology Teflon plain bush bearing are utilized on all gear journals to improve pressure and speed capability.

Motors: are available with capacities ranging from 83 NM to 517 NM @ 1000RPM. Basically similar in design to pumps, they are engineered for extreme heavy duty applications, with high efficiency characteristics. Motor speed is in direct proportion to the volume of oil delivered to the inlet port and output torque is in proportion to the pressure supplied to the motor. All other equipment required to match our pumps and motors is readily available.

Interchangeability

GPM hydraulic equipment is direcUy interchangeable with the other internationally recognized SAE pumps and motors. GPM equipment is sold in component form but units can be assembled and tested to meet your particular requirements.

PL Factor

Each section of a pump or motor should be regarded as a single unit with corresponding power input requirements. The entire input horsepower is fed through the drive shaft, the power delivered to or from the unit is limited by the strength of the shaft. The limit is defined as the “PL” factor. The “P” being the operating pressure In PSI and the “L” the sum of the gear widths in Inches.

In multiple units the “PL” must be calculated for each connecting shaft and must include the sum of the gear widths driven by it. (Each shaft has a unique “PL” factor as can be seen in the table below).

Pressure (PSI) x Total Gear Width (Inches) = PL Factor

PL FACTOR MUST NOT EXCEED FIGURE SHOWN IN CHART FOR SHAFT TYPE
GPM Bushing Pumps Shaft Types

Quick Reference Exploded View

GPM Bushing Pumps Exploded View

Quick Reference Parts List (A to G)

GPM Bushing Pumps Quick Reference A-G

Quick Reference (A) - Solid Shaft Gear Set - Series 215, 230, 250

GPM Bushing Pumps Quick Reference A1

Quick Reference (A) - Solid Shaft Gear Set - Series 265

GPM Bushing Pumps Quick Reference A2

Quick Reference (B) - Loose Gear Set

GPM Bushing Pumps Quick Reference B

Quick Reference (C) - Gear Housing

GPM Bushing Pumps Quick Reference C

Quick Reference (D) - Shaft End Covers - Series 215, 230

GPM Bushing Pumps Quick Reference D1

Quick Reference (D) - Shaft End Covers - Series 250, 265

GPM Bushing Pumps Quick Reference D2

Quick Reference (E) - Port End Covers - Series 215, 230

GPM Bushing Pumps Quick Reference E1

Quick Reference (E) - Port End Covers - Series 250, 265

GPM Bushing Pumps Quick Reference E2

Quick Reference (F) - Bearing Carriers

GPM Bushing Pumps Quick Reference F

Quick Reference (G to I) - Thrust Plates, Thrust Plate Seals, Connecting Shafts - Series 215, 230, 250

GPM Bushing Pumps Quick Reference G-H-I

Quick Reference (I) - Connecting Shafts - Series 265

GPM Bushing Pumps Quick Reference I

Bushing Pump Motor Dimensions - Series 215

GPM Bushing Pump & Motor Dimensions-1

Bushing Pump Motor Dimensions - Series 230

GPM Bushing Pump & Motor Dimensions-2

Bushing Pump Motor Dimensions - Series 250

GPM Bushing Pump & Motor Dimensions-3

Bushing Pump Motor Dimensions - Series 265

GPM Bushing Pump & Motor Dimensions-4

Bushing Pump Porting

GPM Bushing Pump Porting

Bushing Pump Torque Settings

GPM Bushing Pump Torque Settings

 

 

GPM Bushing Pumps

 

Contact us about this Pump Range

Contact Details

Our locations

We are located at:  210 Motor Scooter Drive, Nesbit, MS 38651

Our Worldwide Head Office and Manufacturing Facility is located at 15 Moody Avenue, Epping Industria 1, Cape Town, South Africa.   If you are closer to that location and wish to contact them, view their website’s contact page here.

Call us

Our switchboard is open from Monday to Friday from 7:30 – 4:30 Central.  Phone: 662 298 3652

Contact Form